- JHM Solid Linkage and Cross Rod Upgrade for B9-A4 6-Speed Manual
JHM Solid Linkage and Cross Rod Upgrade for B9-A4 6-Speed Manual
Exhaust - Race Pipe - Stainless Steel (JHM) for B9 S4-S5 3.0T$1,199.95Add to Cart | Wishlist
JHM HD Linkage Cross Rod (Early) for B5-S4, C5 A6-allroad$199.95Add to Cart | Wishlist
JHM Oil Separator Heater Bypass Kit for B8-S5 4.2L FSI V8$11.95Add to Cart | Wishlist
Introducing the JHMotorsports Solid Linkage and Cross Rod Upgrade for your B9 Chassis Audi!
PROUDLY DESIGNED AND BUILT AT JHM IN LATHROP, CA!!!
Here at JHM, we have been developing and building shifter and linkage upgrades for Audis since 2006. As we've done for the B5, B6, B7 and B8 platforms, we're bringing the JHM "Solid" shifting experience to your B9 Chassis Audi with our B9 Solid Linkage and Cross Rod Upgrade!
While Audi has improved on their OEM shifter setup since the days of the incredibly sloppy B5, they still use primarily plastic and rubber components in their B9 linkage. This contributes to the vague and somewhat rubbery feel you experience while shifting your B9 Audi and makes the linkage alone worse than previous generations. Furthermore, as plastic ages it gets brittle and tends to break easily.
If you are looking for the ultimate shifting experience with precise feedback allowing for confident gear changes, the JHM B9 Solid Linkage and Cross Rod Upgrade is what you need. Our JHM B9 Linkage and Cross Rod setup is the ultimate upgrade for increasing the durability and longevity of your linkage components while dramatically improving the shifting experience of your B9 Audi.
Adding our JHM Linkage and Cross Rod or a JHM Solid Short Throw Shifter alone won't bring much noise or vibration into the cabin due to Audi's ultra-silent, rubber lined shift knob. However, if you're looking for the ultimate shifting experience with more of a race inspired setup, we recommend our Linkage, Shifter, and Shift Knob which can all be found in the same section as this product. NOTE: Adding in our shift knob and other variables like your exhaust setup, other lightweight/performance components (crank pulleys, flywheels, etc...), and factory tolerances may affect how much of an increase in interior noise, vibration and/or harshness you experience. Remember, Audi designed these components with lots of plastic and rubber to hide normal noises that the engine and transmission make so removing them can reveal some of those noises.
This linkage and cross rod upgrade is a direct replacement for the OEM components. Our JHM Linkage and Cross Rod replaces the OEM plastic socket assemblies on both the linkage and the cross rod with 2 spherical steel bearings and one graphite impregnated, polyurethane bushing.
On the linkage, we put a steel spherical bearing in a custom race at the end of the shift rod or selector shaft.
JHM Cross Rod
Matching exactly the OEM dimensions, we attach our Cross Rod upgrade to a cage on top of the race using another, smaller spherical rod end housed in a bronze race for more rigid side to side feel. On the other end of the Cross Rod at the selector shaft cap on the transmission, we use a heavy duty, graphite impregnated, polyurethane bushing.
Not only do these spherical and polyurethane bushings offer much more precise shifting while delivering more feedback than stock but they are also much more durable than the OEM plastic setup.
Our JHM B9 Solid Linkage and Cross Rod Upgrade will deliver the ultimate shifting experience when paired with our JHM B9 Solid Short Throw Shifter. However, it will also dramatically improve your shifting performance if you only have a stock or aftermarket shifter.
- 1x JHM Solid Linkage and Cross Rod Assembly
Due to the design of the OEM cross rod and linkage setup, the most cost effective way to upgrade the shifting experience was to combine our JHM Solid Linkage and JHM HD Cross Rod Linkage into one "Solid Linkage and Cross Rod Upgrade."
For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.
|Audi||A4||B9 (2017-Present)||2.0t TFSI|
By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system. Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.
As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).
Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.
Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
Learn More: www.p65warnings.ca.gov
Select options & add to cart to view final price