- Front Rotors(pair)-JHM 330mm for Cayenne Caliper on C5-A6-S6 4.2L
Front Rotors(pair)-JHM 330mm for Cayenne Caliper on C5-A6-S6 4.2L
JHM Supercharger Kit for B8-S5 w/ 4.2L FSI V8, Stage 1
Select options & add to cart to view final price
JHM HD Linkage Cross Rod (Early) for B5-S4, C5 A6-allroad$199.95Add to Cart | Wishlist
**NOTE: As of 8/1/2012, all JHM Lightweight Rotors will now look like the picture below!!!***
Click to enlarge picture
Due to popular demand, all of our 2-piece, lightweight rotors will now come with black anodized rotor hats featuring Type 3, hard anodizing, the highest quality and hardest anodizing available for aluminum. This will make the rotor hats more resistant to fade and wear and will hide brake dust better. Due to popular, demand all lightweight rotor rings will also feature zinc plating. This high quality coating will slow the effects of corrosion and keep your rotor rings looking good through the winters.
IN STOCK AND READY TO SHIP! FINALLY a low cost front BBK (Big Brake kit) solution for your C5-A6-S6 with the 4.2L V8 that uses the popular Porsche Cayenne caliper (6-piston Brembo) while clearing most OEM 17" wheels and most aftermarket 17" wheels as well. We have confirmed fitment on B5 S4 oem wheels (similar to B6 A4 USP wheels) and found that there was a bunch of room. Also we confirmed fitment on the 17" BBS wheels shown in the picture below. Click to enlarge picture
Stock 321mm vs. JHM 330mm 2-piece for the Porsche Cayenne Caliper
-Rotor OD: Stock = 321mm(12.6"), JHM = 330mm(13") - .4" larger
-Rotor Thickness: Stock = 30mm(1.18"), JHM = 32mm(1.26") - thicker
-Rotor Weight: Stock = 21lbs(each), JHM = 19.5lbs(each) - 7% LIGHTER, 1.5lbs less each
-Rotor Cooling Air-gap: Stock = 11mm(.433"), JHM = 15.5mm(.610") - LARGER for better cooling
-Rotor Cooling Center Fin Design: Stock = Straight Fin, JHM = Airfoil - MORE EFFICIENT for better cooling
-Bolt pattern: - SAME (fits like an OEM rotor would) Why the Porsche Cayenne caliper? With its 6-piston design and MASSIVE brake pads it is a strong performer. Also it bolts right up to your spindles with NO brackets. All you need is some bolts, nuts, brake lines and JHM rotors and you have a 350mm BBK. Being that it is an OEM part they are readily available and can be found used for great prices. INCLUDES: 2 - JHM 2-piece Lightweight Slotted Front Rotors. OPTIONS:
- Go back one section if you need a hardware kit for adapting the calipers to your car (bolts, washers and nuts).
- Go back one section if you need need stainless brake lines that adapt these calipers to the B6/B7 A4. Outer ring specs:
We worked closely with a race brake manufacturer that supplies many NASCAR racers and a couple major brake kit companies. Due to their expertise we chose to have them build us the outer rings to our specs to fit the B6-B7 S4-A4 with a Cayenne caliper bolted on. 12 attachment points for durability and strength. Center hat specs:
We CNC machine the Aluminum center hats in house based on their recommended materials and thicknesses for durability. 12 attachment points for durability and strength. We also engrave JHM in them in 3 locations equal from each other, it looks clean and doesn't jump out or look tacky. Click to enlarge picture
INSTALLATION NOTES AND PICTURES HERE
NOTE: The C5 A6-S6 4.2l V8 spindles sometimes have excess material where the caliper mounts to the spindle at the upper mount point. This takes the caliper out of parallel to the rotor. Check for this by installing the caliper and rotor with no pads and checking that the outer pins are the same distance from the rotor (make sure you have the rotor flat and installed with 5 bolts). If the top pin is much closer or touching you need to shave down the upper mounting point until the caliper is parallel with the rotor. Also you will notice that the caliper is closer to both outer pins vs the outer pins, this is ok and as designed. This outward bias is there to give max clearance for the rotor from the spindle and for optimum performance. Unfortunately this is a mass produced cars and inconsistencies do happen from time to time in the manufacturing of a car. This is a quick fix and once the caliper is parallel the kit will install easily.
Note - This brake upgrade only fits under 17" wheels or larger. It fits stock 17" B5 S4 wheels (similar to OEM B6 A4 USP wheels) with NO wheel spacer and most other OEM and aftermarket wheels as well.
Please note: JH Motorsports does not recommend using EBC brake pads with our 2-piece lightweight rotors. Customer have reported and we have found EBC pads leave excessive pad deposits that can cause brake pulsation. Many EBC pads have a break in coating that reacts with the zinc plating used on our rotors
For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.
|Audi||S6||C5 (2002-2003)||4.2l V8 40v|
|Audi||A6||C5 (1998-2004)||4.2l V8 40v|
By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system. Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.
As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).
Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.
Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
Learn More: www.p65warnings.ca.gov