JHM B5-S4, C5 A6-allroad 2.7T engine (originally 01E) 0A3 6-Speed Manual Transmission Conversion-Swap Parts List
NOTE: We don't recommend the RS4 0A3 transmissions in a B5 or C5 due to much lower ratios than the B6-B7 S4 and much higher cost to acquire. ELECTRONICS
1 x JHM B5 C5 Speedometer converter for B6-B7 S4 0A3 transmission conversion-swap CLICK HERE TRANSMISSION AND CLUTCH PARTS
1 x JHM B5 C5 Trans Mount Bracket Kit for B6-B7 S4 0A3 transmission conversion-swap CLICK HERE
B5 S4 = 1 x pair B6-B7 S4 or RS4 front axles
C5 A6-allroad 2.7t = 2 x RF B6-B7 S4 or RS4 front axles due to wider A6-allroad wheelbase.
2 x Right Front C5-allroad 6MT CV shafts. Must be from an allroad MT car only.
2 x B5 S4 and C5 A6 2.7t 01E Trans mounts, we recommend 034 street density available on our site. PN=034-509-4046
1 x Set of B6-B7 S4 0A3 transmission to block bolts. **
1 x B6-B7 S4 0A3 transmission. (note, reuse 01E spacer and dowels.) Also the crank sensor needs to have the aluminum spacer removed that it originally had for the 01E)
1 x B5 S4 2.7t clutch and flywheel combo (Our performance options work very well with the 0A3)
1 x B6-B7 S4 shift rod setup (all 3). NOTE: The body does need clearancing for the B6 rods sometimes due to rods being shorter and sitting more forward in the car, also when using a JHM shifter it helps to clearance for the back two shifter assembly mount holes to access the bolts due to the spacers.
1 x B6-B7 S4-RS4 OEM or JHM shifter. These are clamp on knob, you can run B5-S4 or C5 A6-allroad 01E shifters but they must be 01.5 and up with an angled base, keep in mind the B6-B7 shifter is much better.
1 x B5-C5 plastic shifter box and boot only.
1 x B6-B7 S4-RS4 0A3 Drivers side front CV shaft shield.
1 x B6-B7 S4-RS4 0A3 Passenger side front CV shaft shield.
6 x CV shaft shield bolts.
1 x B6-B7 S4-RS4 0A3 Rear driveshaft shield.
2 x Driveshaft shield bolts. DRIVESHAFT AND REAR DIFF PARTS
B5 S4 = 1 x B5 A4 5-speed Rear diff- Diff code DAJ with 3.89 ratio to match B6-B7 S4 transmissions front diff ratio. NOTE: You MUST swap your B5 S4 larger 110mm output shaft flanges to the A4 rear diff with smaller 100mm flanges. This is just one bolt each and a good time to replace the seals and fill the rear diff with fresh fluid. All parts we stock.
C5 A6 = 1 x C5 A6 2.8L 5-speed Rear diff- Diff code EUT with 3.89 ratio to match B6-B7 S4 transmissions front diff ratio.
1 x ADAPTED 01E DRIVESHAFT (MAKE IT SHORTER BY 1.25" on the front side of the center bearing). Any good driveshaft shop can do this, expect to pay between $250 to $400 depending on your shop. This is because they need to cut the shaft, remove material and then rebalance both the front and rear sections. Keep in mind it is a great time to get a 034 driveshaft bearing from us, 2 x driveshaft boots (they are torn a lot which is bad for the joints) and or cv joints as needed to freshen it up and keep vibrations down. REUSE OR SOURCE THESE 01E parts if you do not have them.
1 x Crank sensor.
1 x Driveshaft - to be modified as per above.
1 x Starter.
1 x B5-C5 clutch master cylinder.
1 x B6 S4 early slave cylinder.
1 x JHM stainless clutch line (OEM works too but is more difficult install).
1 x B5 S4 - C5 A6-allroad 2.7t clutch and flywheel combo ( Our performance options work very well with the 0A3)
2 x Engine dowels for 01E Transmission and Spacer - OEM PN 01E301153B
1 x Engine to Transmission spacer for 01E Transmission - 11.2mm thick, this is VERY important to be correct - OEM PN 01E103551C
1 x B5-C5 Clutch pedal assembly with all 3 pedals.
1 x Wiring and pigtails for clutch pedal assembly.
1 x Shift boot and bezel specific from a 2000-2004 MT C5 A6 or allroad. NOTE: the 02 and up have a clamp on knob.
1 x Shift knob. OEM or JHM. OEM are more difficult to find if you are switching from a screw on knob to clamp on or visa versa If you have an questions regarding this swap/conversion, please don't hesitate to reach out to us. We have done this swap/conversion several times and can help you through any step of the way. If you are having troubles locating some of these parts, we can get them for you. Shoot us an email at Sales@JHMotorsports.com. NOTE: THIS IS NOT A PRODUCT THAT IS FOR SALE. THIS IS A LIST THAT WE HAVE MADE PUBLIC TO HELP YOU GATHER THE COMPONENTS NEEDED TO USE A 0A3 TRANSMISSION IN YOUR B5 S4, C5 A6 or allraod WITH 2.7T ORIGINALLY EQUIPPED WITH AN 01E. DO NOT PURCHASE THIS.
|Audi||allroad||C5 (2001-2005)||2.7t V6 30v|
|Audi||S4||B5 (1997-2002)||2.7t V6 30v|
|Audi||A6||C5 (1998-2004)||2.7t V6 30v|