Select Vehicle From Dropdown

Torque Mount, Snub Mount (034Motorsport-Density) for B7-RS4 and C5-RS6

SKU: 034-509-2012
This product also fits the 2003 to 2004 RS6 w 4.2l Twin Turbo V8.

This is the latest mount from 034Motorsport in their incredibly successful DENSITY LINE Mount Series. We contacted our friends at 034Motorsport and had them bring their tried and true DENSITY LINE Mounts to the B7-RS4. They built these mounts for us in a few short months. We knew they would work great since we have used their Density Line Mounts on our in house and customers' B5-S4s and B6-B7 S4s for many years. Our record setting B5-S4, B6-S4, and B7-RS4 have already featured 034Motorsport's Density Line Mounts.

This STREET DENSITY Mount is a solid rubber mount with a 65 durometer stiffness. This translates to about a 30% increase in stiffness over your stock mount. This means that the mount will still ride smooth and quiet but provide a marked improvement in locking down the motor when compared to the stock mount. Livable street performance with serious sport intentions.

Not only does this mount cost over 75% less than the factory mount, this mount will also last longer than your factory mount, reduce engine movement, improve throttle response, and improve shifter feel.

If your torque mount is damaged this is a must have. It's also good to replace this mount whenever you have your front end off for a belt replacement or JHM Lightweight Crank Pulley installation.

NOTE: THIS IS NOT AN OE MOUNT. THIS MOUNT IS NOT AVAILABLE FROM ANY OTHER SOURCE. These are built by an OE supplier to 034Motorsport's specifications.

FITMENT: This mount will fit all B7-RS4s and C5-RS6 Twin Turbo 4.2l V8s. This piece replaces OEM PN 4B3199267 or 4B3 199 267.
NOTE: These mounts sometimes have cosmetic blemishes in the steel casings which occur in transit from 034Motorsport's manufacturer to their location. The rubber is so deeply embedded in the steel casing during the manufacturing process that this does not affect durability or performance of the mount.

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.

This product fits the following vehicles:
Make Model Chassis Engine
Audi RS4 B7 (2006-2009) 4.2l V8 32v FSI
Audi RS6 C5 (2003-2004) 4.2t V8 40v
Write Your Own Review
You're reviewing: Torque Mount, Snub Mount (034Motorsport-Density) for B7-RS4 and C5-RS6
Off-road Use

By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)

Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system.

Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.

As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).

Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.

Prop 65

Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.

Learn More:

Q and A

Product Questions

No questions yet. Be the first to ask the question!