- Strut Mount, Street Density, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3/TT/TTS (MQB)
Strut Mount, Street Density, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3/TT/TTS (MQB)
We're proud to announce the availability of the Density Line Strut Mount for MkVII Chassis Volkswagen and 8V & 8S Chassis Audi models!
034Motorsport's Density Line Mounts are the new standard in comfort and performance. Our mounts are redesigned with performance in mind, and manufactured from high-durometer rubber for increased performance and durability, without sacrificing comfort. Density Line Mounts are void-free and fluid-free, eliminating the slop associated with the factory mounts.
The Street Density Strut Mount is manufactured from 70 durometer rubber, which is approximately 50% stiffer than stock. The rubber is also fully vulcanized to the center cups to increase the lifespan and performance of the mounts significantly.
The steel strut mount bodies have also been redesigned to cope with the added stresses of spirited driving.
The result is a significant reduction in deflection of the strut mount. These mounts will also eliminate the annoying "squeaking" sound often caused by the stock strut mounts when paired with coilover suspensions. Street Density Strut Mounts will only cause a minimal increase in noise, vibration, and harshness (NVH) inside of the cabin. These mounts are a completely re-engineered performance solution, not just inserts for use with the factory mounts.
- Manufactured from 70 Durometer Rubber
- Rubber Fully Vulcanized to Center Cups
- Eliminates "Squeaking" Sound Caused by Factory Strut Mounts
- Reduced Strut Mount Deflection
- Maintain Proper Suspension Geometry Under Load
- Improved Steering Feel & Handling
- Complete Drop-In Replacement of Factory Strut Mounts
- Priced Individually - Two Required Per Vehicle
- 2015 - Present Audi A3/S3 (8V)
- 2014 - Present Audi TT / TTS (8S)
- 2015 - Present Volkswagen Golf / GTI / R (MkVII)
- 5Q0 412 331D 5Q0412331D
- 1 Year Limited Replacement Warranty (If you encounter any issues with our products outside of the warranty period, we will work with you to provide a resolution.)
High-Durometer Rubber vs. Polyurethane:
Density Line Mounts are manufactured from high-durometer rubber instead of polyurethane for a number of reasons. While vulcanized rubber mounts are more expensive to prototype due to increased complexity of manufacturing and high initial tooling costs, rubber is inherently better than polyurethane as a damping medium for mounts and bushings.
Rubber is able to deal with stress under both tension and compression, while polyurethane mounts rely on the damping medium to be effective only under compression. Rubber is also excellent in shear, where polyurethane is ineffective, making it ideal for suspension bushings that apply a shear force to the bushing during articulation.
Rubber does not pack and wear like polyurethane does, which ultimately results in a long-lasting part with consistent performance and comfort.
While the redesigned Volkswagen/Audi strut mount for the MkVII and 8V/8S chassis was a great improvement over the previous generations of strut mounts, they leave much to be desired when paired with performance dampers or coilover suspensions.
Many owners experience a "squeaking" sound coming from the front strut mounts after installing performance dampers or coilover suspensions. The noise becomes noticeable when pulling out of driveways, going over speed bumps, or traveling at low speed over uneven surfaces.
This "squeaking" is caused by the low durometer rubber used in the factory strut mounts, which causes the steel center cup to move inside of the rubber mount. Our Track Density Strut Mount Pair was designed to eliminate this annoying issue, and improve the performance of the vehicle's suspension.
Please Note: One vehicle requires 2 mounts.
|MK VII (2015-Present)
|MK VII (2015-Present)
|MK VII (2015-Present)
|MK VII (2015-Present)
By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system. Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.
As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).
Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.
Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
Learn More: www.p65warnings.ca.gov