Select Vehicle From Dropdown

JHM Aluminum Lightweight Flywheel and Clutch Combo for B8 S4-S5 w/ 3.0T FSI


Select options & add to cart to view final price
From: $1,800.00

To: $2,025.00

* Required Fields




After two years of research, development, prototyping, and testing we are finally ready to release our long awaited Lightweight Flywheel and Clutch Combo for the B8-S4 and B8-S5 with the 3.0T FSI! We began developing this kit in 2011 and have already installed it on several cars.We like to test all of our products for an extended period of time to verify the durability and longevity of the part before selling it publicly.


In addition to working with our JHM Performance Clutch Kit , we have designed our JHM Lightweight Flywheel for the B8 S4-S5 so that it will work with an OEM stock clutch kit or ANY aftermarket clutch kit designed to work with the OEM B8 S4-S5 Flywheel.


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S8


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S9


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S10


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S11


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S12


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S5 w/ 4.2L FSI V8





The OEM Flywheel on the B8 S4 and S5 is a completely new design and a significant departure from Audi's previous flywheel designs. Instead of having the traditional single piece flywheel (i.e. the traditional "dual-mass flywheel") that just bolts to the back of the motor, the B8 S4-S5 flywheel is a two-piece, hourglass shaped, unit which allows Audi to position the motor further back in the chassis for better weight distribution. This is achieved by running a half-shaft through the narrow part of the hourglass shape in the flywheel. This major design change presented a new challenge for us.


OEM B8-S5 FLYWHEEL, 2-PIECE: B8 S4-S5 4.2L V8 and 3.0T Flywheels are dimensionally the same with the only differences being small weight variations and different part numbers.


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S5


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S6


Beginning in 2011, we tested out our Lightweight Flywheel concept by drilling out the rivets on the OEM unit and re-using the lower half of the OEM flywheel. We replaced the upper, cast-iron, dual-mass flywheel piece with a prototype version of a lightweight aluminum piece that we built in house. Once we were satisfied with the performance of our prototype, we went on making our own lower base out of machined steel, which can be seen above. This was done by completely re-engineering the overall unit for an optimal balance of strength and weight reduction.


Click to enlarge picture
Audi JHM Lightweight Flywheel for B8-S7





Replacing the OEM, cast-iron, dual-mass flywheel with a single-mass, lightweight, aluminum piece reduces the overall weight of the rotating assembly of the motor. This frees up power in the motor and leads to increased throttle responsiveness. Changing the upper portion of the OEM flywheel to a single-mass unit also eliminates the potential for failure of the dual-mass unit. This is especially important on high-horsepower cars. Finally, the JHM Lightweight Flywheel offers the additional advantage of having a removable friction liner. If you end up replacing your clutch and pressure plate at a later date, you don't need to replace the entire flywheel OR worry about re-surfacing it (which - as of August 2013 - has yet to be done successfully for this large of a unit). Resurfacing would also not be cost effective due to tooling and fixture costs for such a tall, dual-mass flywheel. All you need to do is just replace the removable friction liner.





Our Lightweight Flywheel and Clutch Combo comes with our JHM B8 S4-S5 Performance Clutch. This clutch kit features an upgraded, OEM Luk pressure plate with an increased clamp load of over 150 pounds more than the OEM pressure plate while still retaining the self adjusting clutch mechanism (SAC). Increased clamp load leads to greater torque holding capacity without the use of overly aggressive clutch disc friction materials.


For the clutch disc, we have 3 different options to run with our lightweight flywheel and clutch combo:
STAGE 1: Our Stage 1 Disc is the OEM B8 S4-S5 organic disc. This disc - paired with the increased clamp load of our upgraded pressure plate - gives the best compromise between increased holding power and maintaining the OEM feel of clutch engagement. This is recommend for stock or near stock vehicles with basic bolt-on upgrades that aren't driven aggressively.
STAGE 3: Our Stage 3 disc is a Ceramic and Metal Backed Organic disc meaning that the material that contacts the pressure plate is an organic material with metal integrated into the material. The side that contacts the flywheel is ceramic. This combination of materials will give you a much more direct engagement as compared to the stock disc, while still remaining very easy to daily drive. This clutch disc is recommended for FULL BOLT-ON cars that are driven aggressively and/or light duty track use.
STAGE 4: Finally, our Stage 4 disc is a Ceramic and Kevlar disc. Kevlar is the material facing the pressure plate and the ceramic material is facing the flywheel. This disc will engage slightly more aggressively than our Stage 3 disc and is still very streetable. The Stage 4 Disc will give you the most torque holding capacity over all three setups. The only downside to this disc is the extended break-in period. See below for more information on the break-in procedure.


Select your clutch stage from the dropdowns below before adding this product to your cart.


Click to enlarge picture


Click to enlarge picture
Audi B8 S5 Performance Clutch







FLYWHEEL SPECIFICATIONS: At JHM, we have weighed over a dozen OEM flywheels. We have seen a wide range of weight variances even on flywheels with the same part number! On average, the JHM Lightweight Flywheel weighs 8 to 10 lbs less compared to the OEM B8 3.0T Flywheel. When compared to the OEM 4.2L V8 Flywheel the JHM unit weighs 7 to 10 lbs less.



- Upgraded, OEM Luk pressure plate with 150 lbs more clamp load over stock pressure plate.
- Stage 1 Clutch Disc with Organic Material
- Stage 3 Clutch Disc with Ceramic and Metal Backed Organic Material
- Stage 4 Clutch Disc with Ceramic and Kevlar Material



- JHM Aluminum and Machined Steel 2-Piece Lightweight Flywheel
- 6x Flywheel to Flexplate Bolts
- 1x JHM Upgraded, OEM-Luk Pressure Plate
- 1x Clutch Disc - Stage 1 (OEM Organic), Stage 3 (Ceramic-Metal Backed Organic), or Stage 4 (Ceramic-Kevlar). Select your Disc Material from the dropdown below
- 6x Pressure Plate to Flywheel Bolts
- 1x OEM B8 S4-S5 Throwout Bearing
- 1x OEM B8 S4-S5 Guide Sleeve



FITMENT: All B8 S4-S5s with 6-speed manual transmissions and the 3.0T FSI Motor. Additionally, we have designed our JHM Lightweight Flywheel for the B8 S4-S5 so that it will work with an OEM stock clutch kit or ANY aftermarket clutch kit designed to work with the OEM B8 S4-S5 Flywheel.


- B8 S4 with 3.0T FSI V6
- B8 S5 with 3.0T FSI V6



INSTALLATION INSTRUCTIONS AND TORQUE NOTES: These are NOTES ONLY are not a substitute for factory installation manuals or technical expertise. They are to be used a supplemental guideline only. We always recommend that an experienced technician perform ALL clutch and flywheel installations. For shops or individuals who have access to factory manuals but not factory tools, here are some tips and guidelines we have used to complete this job without the factory tools:
- The JHM Lightweight Flywheel installs in the same manner as the OEM Flywheel. Follow the OEM installation and torque procedures.
- Aligning the clutch disc, pressure plate, flywheel assembly: Install the throwout bearing/sleeve onto the transmission. For alignment of the clutch disc it is easiest to put the flywheel face-up, place and align the disc splines on center with the center bearing in the flywheel, put the pressure plate on top, visually check that the disc is still on center, and begin to tighten and torque the pressure plate. The pressure plate bolts need to be secured with red, high-strength Loctite. Make sure the pressure plate bolts are tightened in a star pattern at multiple torque intervals. This is to make sure that the pressure plate diaphragm or fingers are not distorted upon installation. Once the pressure plate is fully torqued to the flywheel with red Loctite to factory specifications (33 ft-lbs, in intervals), the clutch, pressure plate, and flywheel combination can now be slid onto the transmission as you would a torque converter on an Automatic Transmission. If the assembly will not slip on the transmission, this is most likely due to the fact that the disc is not on center. Remove the pressure plate and attempt to re-align the disc. **NOTE: We've successfully aligned the assembly by following the above procedure. It is not that difficult to "eyeball" the alignment.
- Once the clutch and flywheel combo are installed in the transmission, the half-shaft can be re-installed (this prevents the clutch and flywheel from falling out of the transmission while attempting re-installation). Install and bolt the transmission to the engine. Install the JHM supplied bolts for attaching the flywheel to the flexplate. Torque the flyweel to flexplate bolts to factory specifications. This is done in a similar fashion to torquing down a torque converter to a flexplate on an Automatic Transmission.



BREAK IN PROCEDURE: Clutch break-in is important and must be done properly.


During the break-in period ALL racing activities, launching, or aggressive driving that get the clutch hot MUST be avoided!!! For the Stage 3 clutch clutch disc you need to drive about 500 miles of city type driving. Each time the clutch disc is disengaged and reengaged slowly - basically, whenever you start from a stop or shift it aids in break-in. Because of this, highway mileage does not count. For Stage 4 clutch discs you need to drive about 750 miles of city type driving. Due to Kevlar's resistance to wear, it takes longer to break in.


NOTE: For those that are looking for a more robust, race oriented clutch setup we highly recommend looking into our R-Series line-up that does not have an SAC. The SAC in OEM and other aftermarket pressure plates work great for comfort and OEM-like drive-ability, however it is not designed to take excessive abuse of track days or aggressive street driving. We have done rigorous testing since 2012 to develop the ultimate clutch solution for both street and track and the R-Series is what is needed to take these cars to the next level.


For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.

This product fits the following vehicles:
Make Model Chassis Engine
Audi S5 B8-B8.5 (2008-2017) 3.0t V6 24v SC
Audi S4 B8-B8.5 (2010-2016) 3.0t V6 24v SC
Write Your Own Review
You're reviewing: JHM Aluminum Lightweight Flywheel and Clutch Combo for B8 S4-S5 w/ 3.0T FSI
Q and A

Product Questions

No questions yet. Be the first to ask the question!
You may also be interested in the following product(s)