Select Vehicle From Dropdown

JHM Lightweight Flywheel (Aluminum) and Clutch Combo for B7 RS4

SKU: JHM-RS4LWFWCC-aluminum

Select options & add to cart to view final price
From: $1,025.00

To: $1,300.00

* Required Fields

Details
Details

SPECS 

- ALUMINUM FLYWHEEL USA MADE - These JHM aluminum lightweight flywheels weigh less than 1/2 the weight of stock! 13lbs versus 26.5lbs for B7 RS4. These are a direct replacement for all B7 RS4s. The iron friction liner is replaceable, so, you will never have to buy a new flywheel again, you can just swap the liner if you ever replace your clutch. The crank position ring is welded to the ring gear while being retained and fastened with countersunk screws (not cheap pins prone to shearing like some other brands). For those concerned about the driveability and the infamous "chatter" of a lightweight flywheel that Audi enthusiasts have experienced with smaller 4 cylinder and 6 cylinder turbo engines here is the truth. With the B7 RS4s 4.2L V8s torquey nature the driveability is very close to stock and the noise is minimal when it is bogged under 1500 rpm. Some of JHMs customers have reported that they did not notice it at all.
- CLUTCH - These JHM Stage 3 (hybrid Ceramic/Metal Backed Organic) street performance clutches (choose stage below before ordering) are from a result of actual on car testing (video proof above) and from pressure plate clamp load testing that JHM had performed on all the available pressure plates for the B6/B7 S4 and RS4. Most of the on car testing was to find the optimal materials for the most streetability while delivering the performance any Naturally Aspirated B7 RS4 could dish out. As for driveability the hybrid combination of materials has made the clutch hold better and handle higher heat as well while still being smooth enough for every day driving with a stock like pedal feel.

 

Why a lightweight flywheel? Well when you reduce the weight of the rotating mass on the engine you free up horsepower. So that is the great benefit of a lightweight flywheel, plus the JHM unit is less expensive than a brand new OEM flywheel and it doesn't have a dual mass setup that can wear out or fail.

 


Click to enlarge picture
Audi B7 RS4 Performance Clutch

 

Click to enlarge picture
Audi B7 RS4 Performance Clutch

 

Click to enlarge picture
Audi RS4 Lightweight Flywheel & Performance Clutch

 

Click to enlarge picture
Audi RS4 Lightweight Flywheel & Performance Clutch

 

INCLUDES THE FOLLOWING -JHM Aluminum Lightweight flywheel built to B7 RS4 specs - New pilot bearing (already pressed in) - Flywheel to crank bolts - B7 RS4 pressure plate - JHM Stage 3 (hybrid Ceramic/Metal Backed Organic) disc (choose stage below before ordering) - Pressure plate to flywheel bolts - Throwout bearing - Clutch alignment tool.

 

INSTALLATION AND TORQUE NOTES HERE

 

NOTE: Clutch break in is important and must be done properly. For the Stage 3 clutches you need to drive as much city type driving as you can for the first 500 miles (each time you start from a stop or shift it aids in break in, Highway mileage does not count). 

NOTE: For those that are looking for a more robust, race oriented clutch setup we highly recommend looking into our R-Series line-up that does not have an SAC. The SAC in OEM and other aftermarket pressure plates work great for comfort and OEM-like drive-ability, however it is not designed to take excessive abuse of track days or aggressive street driving. We have done rigorous testing since 2012 to develop the ultimate clutch solution for both street and track and the R-Series is what is needed to take these cars to the next level.

 

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.



This product fits the following vehicles:
Make Model Chassis Engine
Audi RS4 B7 (2006-2009) 4.2l V8 32v FSI
Reviews
Write Your Own Review
You're reviewing: JHM Lightweight Flywheel (Aluminum) and Clutch Combo for B7 RS4
Off-road Use

By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)

Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system.

Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.

As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).

Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.

Prop 65

Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.

Learn More: www.p65warnings.ca.gov

Q and A

Product Questions

No questions yet. Be the first to ask the question!
You may also be interested in the following product(s)