Select Vehicle From Dropdown

JHM Intake Spacers (8mm thick) for C6-S6 and D3-S8 FSI V10

SKU: JHM-07L133074B-07L133073E-kit

$295.00

* Required Fields

Details
Details

PROUDLY MADE IN THE U.S.A.

 

Introducing the JHM Intake Spacers for the C6-S6 and D3-S8 V10 FSI. They are 8mm thick and CNC machined out of high quality materials.

 

Intake Spacers help bring your intake temperatures down by insulating the intake manifold from the heat coming from the cylinder heads due to combustion. With a cooler intake manifold, you create a cooler and denser intake charge which helps add more torque and horsepower, gear after gear! The intake spacers also increase the length of your V10's intake runners which creates more torque.

 

With our in-house testing, we found gains everywhere throughout the RPM range. The biggest gains were from 5000 to 7000 rpm, with the second best area of gains occurring from 4200 to 6500 rpm. (We identify these gains by analyzing the data from our data-logging and performing acceleration rate calculations in 3rd gear.) The BEST advantage for these intake spacers is that we saw that the car didn't slow down after repeated pulls due to an extremely heat soaked intake manifold bringing the intake temperatures up. Bottom line, the longer we beat on our in-house S8, the better it performed when compared to tests without the intake spacers.

 

These spacers are a great modification for the money, especially on the naturally aspirated (all-motor) V10 FSI engines where every little gain counts!

 

PARTS INCLUDED: The JHM V10 FSI Intake Manifold Spacer Kit will include the following parts:
2x- JHM Intake Spacers (1 for each side of the intake)
2x- OEM Intake gaskets (1 for the each of the top sides of the spacers that mate to the intake manifold.) On lower mileage cars you can reuse the stock gasket between the spacer and the cylinder head. If you're unsure of the condition of your OEM gaskets, select the option below for a second pair of gaskets.
- 12x Stainless steel bolts, that are longer to accommodate the spacer (6 for each side of the intake)
- 12x Washers for the supplied longer bolts (6 for each side of the intake)

 

Additional Gaskets: 

-If you need additional gaskets, search SKUs:  OEM-07L133073E and  OEM-07L133074B

RECOMMENDED:

 

-JHM Oil Separator Heater Bypass Kit: Yes, I want one and will add SKU: JHM-4E0121103S to my cart. This helps keep the intake temperatures even lower and takes very little time (less than 5 minutes) to install with the intake manifold removed. NOTE: Not recommended for extremely cold climates. Go back one section to add this to your cart.

 

-JHM Carbon Cleaning Tool Kit and Solution. During the installation of JHM Intake Spacers is the optimal time to perform a carbon cleaning, as you will have the manifold off and have the valve pockets exposed. Go back one section to add these to your cart.

 

INSTALLATION:
The installation of these intake spacers requires the same labor as a carbon cleaning. So if you're getting a carbon clean performed to bring back top end horsepower on your S6 or S8, why not install our JHM Intake Spacers and add some torque too?! In addition to just removing the intake manifold for a carbon clean, the intake spacers require you to flex and move up the high pressure fuel line distributor by about 10mm (total width of the spacer plus an additional compressed gasket). You'll also need to adjust the fuel lines since the manifold will be sitting about 10mm higher than stock.

 

You will also want to remove wiring harness bracket from the studs on the driver side head. You can secure the wires with a zip tie so they stay out of the way of the flap arms. This is because the brackets can interfere with your flap arms and give you the following codes:

 

008196 - Intake Manifold Flap; Bank 1 P2004 - 002 - Stuck Open - MIL ON

 

008197 - Intake Manifold Flap; Bank 2 P2005 - 002 - Stuck Open - MIL ON

 

Here is a detailed JHM V10 Intake Spacer Installation DIY: CLICK HERE!!

 

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.



This product fits the following vehicles:
Make Model Chassis Engine
Audi S6 C6 (2006-2011) 5.2l V10 40v
Audi S8 D3 (2006-2010) 5.2l V10 40v
Reviews
Write Your Own Review
You're reviewing: JHM Intake Spacers (8mm thick) for C6-S6 and D3-S8 FSI V10
Off-road Use

By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)

Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system.

Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.

As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).

Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.

Prop 65

Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.

Learn More: www.p65warnings.ca.gov

Q and A

Product Questions

No questions yet. Be the first to ask the question!
You may also be interested in the following product(s)