- Engine/Transmission Mount Pair, 8J Audi TT RS 2.5 TFSI, 6-Speed Manual, Street Density
Engine/Transmission Mount Pair, 8J Audi TT RS 2.5 TFSI, 6-Speed Manual, Street Density
We're proud to announce the availability of the Street Density Performance Engine/Transmission Mount Pair for the 8J Audi TT RS 2.5 TFSI 6-MT!
034Motorsport's Density Line Mounts are the new standard in comfort and performance. Our mounts are redesigned with performance in mind, and manufactured from high-durometer rubber for increased performance and durability, without sacrificing comfort. Density Line Mounts are void-free and fluid-free, eliminating the slop associated with the factory mounts.
The Street Density Engine Mount Pair is manufactured from 60 durometer rubber, which is approximately 35% stiffer than stock. Since the mounts are also void-free and solid-filled, the resulting mount is approximately 60% stiffer than stock. The cast aluminum mount bodies have also been redesigned to cope with the added stress of spirited driving.
The result is greatly reduced drivetrain slop, crisper shifting, and minimal wheel hop, without any significant increase in noise, vibration, or harshness (NVH) inside of the cabin. These mounts are a completely re-engineered performance solution, not just inserts for use with the factory mounts.
- Manufactured from 60 Durometer (Street Density) Rubber with Void-Free Construction
- Includes Stainless Steel Accessory Bracket and Necessary Hardware
- Reduced Drivetrain Slop
- Decreased Engine Movement Under Load
- More Direct Power Transfer
- Improved Shifting Feel
- Complete Drop-In Replacement of Factory Engine/Transmission Mounts
- Sold in Pairs (One Engine Mount & One Transmission Mount)
- 2009 - 2013 Audi TTRS 2.5 TFSI (8J)
- 6-Speed Manual Transmission Only!
- 8J0199262G / 8J0 199 262 G
- 8J0199555H / 8J0 199 555 H
- 1 Year Limited Replacement Warranty (If you encounter any issues with our products outside of the warranty period, we will work with you to provide a resolution.)
High-Durometer Rubber vs. Polyurethane:
Density Line Mounts are manufactured from high-durometer rubber instead of polyurethane for a number of reasons. While vulcanized rubber mounts are more expensive to prototype due to increased complexity of manufacturing and high initial tooling costs, rubber is inherently better than polyurethane as a damping medium for mounts and bushings.
Rubber is able to deal with stress under both tension and compression, while polyurethane mounts rely on the damping medium to be effective only under compression. Rubber is also excellent in shear, where polyurethane is ineffective, making it ideal for control arm bushings that apply a shear force to the bushing during articulation.
Rubber does not pack and wear like polyurethane does, which ultimately results in a long-lasting part with consistent performance and comfort.
These mounts are currently available in Street Density only.
|Audi||TTRS||8J (2012-2013)||2.5t TFSI|
By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system. Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.
As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).
Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.
Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
Learn More: www.p65warnings.ca.gov