Select Vehicle From Dropdown

Connecting Rod Set (Integrated Engineering) for 2.7t - No Rifle Drilling

SKU: IEE-IERHVD1
$734.99
Details
Details
Integrated Engineering forged connecting rods for the 2.7T Audi S4.

Features
- 2 Piece Forgings from Vacuum Drawn 4340 Chrome Moly Steel
- Multi Stage Heat Treat for maximum strength, dimensional stability, and fatigue life.
- Fully Machined and Shot Peened
- H-beam Design
- Tolerances as tight as .0003 ground on Sunnen brand equipment
- Standard ARP2000 Rod Bolts
- Computer Optimized Design
- Magnaflux Inspected
- Dimensionally Inspected
- Packed in balanced sets +/- 1 gram.
... All this at a price point that yields market leading value!!!

JHM weighed these rod vs. stock and they about 12 grams heavier per rod. This weight can be easily counteracted with our lighter JE Pistons.

NOTE: Like any other major engine part change (rods-pistons-crank) JHM recommends having your complete rotating assembly (rods-pistons-crank) balanced for best longevity of the motor. However some people have reported that they only did a rod swap and did not have an issue.

INCLUDED ARP 2000 ROD BOLT TORQUE SPECS
*The following torque spec is for the included ARP 2000 5/16" rod bolts using the included ARP assembly lubricant only. Do not follow this guide using ARP +625, other assembly lubricant, or alternative bolts.

STRETCH GAUGE METHOD (best)
The preferred method of measuring bolt load is with a stretch bolt gauge. The included ARP 2000 bolts need to be tightened and measured to .0056" of stretch using the included ARP assembly lubricant.

TORQUE WRENCH METHOD (other if you don't have a stretch gauge)
When using a high quality torque wrench, first verify the torque wrench has not been dropped and is properly calibrated. A un-calibrated torque wrench can lead to under/over torque and rod bolt failure. Torque each rod bolt to a final torque of 26 ft/lbs. We recommend torquing the bolt, breaking it loose, and re-torquing the bolt 3 times per bolt. This ensures proper rod bolt stretch and that the rod cap is fully seated. Do not exceed 26 ft/lbs. This torque spec is based off the included ARP assembly lubricant.

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.


This product fits the following vehicles:
Make Model Chassis Engine
Audi S4 B5 (1997-2002) 2.7t V6 30v
Audi allroad C5 (2001-2005) 2.7t V6 30v
Audi A6 C5 (1998-2004) 2.7t V6 30v
Audi RS4 B5 (1999-2001) 2.7t V6 30v
Reviews
Write Your Own Review
You're reviewing: Connecting Rod Set (Integrated Engineering) for 2.7t - No Rifle Drilling
Off-road Use

By Purchasing any Off-Road use ONLY products from JH Motorsports, Inc. I acknowledge and understand the following disclosure. (This notice is located at the bottom of the page description of affected products on our website.)

Vehicle Code § 27156:
(b) No person shall operate or leave standing upon a highway a motor vehicle that is required to be equipped with a motor vehicle pollution control device under Part 5 (commencing with Section 43000) of Division 26 of the Health and Safety Code or any other certified motor vehicle pollution control device required by any other state law or any rule or regulation adopted pursuant to that law, or required to be equipped with a motor vehicle pollution control device pursuant to the National Emission Standards Act (42 U.S.C. Secs. 7521 to 7550, inclusive) and the standards and regulations adopted pursuant to that federal act, unless the motor vehicle is equipped with the required motor vehicle pollution control device that is correctly installed and in operating condition. No person shall disconnect, modify, or alter any such required device.
(c) No person shall install, sell, offer for sale, or advertise any device, apparatus, or mechanism intended for use with, or as a part of, a required motor vehicle pollution control device or system that alters or modifies the original design or performance of the motor vehicle pollution control device or system.

Health and Safety Code § 43000:
43001. The provisions of this part shall not apply to:
(a) Racing vehicles.

As the aforementioned code sections outline, it is against the law to operate or use a vehicle on public streets or highways with modified, altered, or disconnected motor vehicle pollution control devices. This may include but is not limited to, Evaporative Fuel Controls, Catalysts, DPF, PTOX, PCV Systems, Exhaust Gas Recirculation Systems, Oxygen Sensors, Thermostatic Air Cleaners, Air Intake Systems, Fuel Injectors, Regulators, Adjustable Cam Gears, ECU Programming, Mapping, or other Computer Modifications. Air Pumps, Air Injection, Timing, and any other Emission System Modification(s).

Purchaser acknowledges and certifies to JH Motorsports Inc., that Purchasers vehicle will only be used for racing applications or off road vehicle use only. Purchaser requests these modifications for the purpose of enhancing the vehicle for competitive Racing Applications and will not use this vehicle on public streets or highways. Purchaser agrees to indemnify JH Motorsports Inc., all employees, officers, owners, and subsidiaries for any civil or criminal liability arising out of use of Purchasers vehicle on public streets or highways as Purchaser has been duly notified of the laws and regulations regarding disconnecting, alteration, or modification of a vehicle’s pollution control devices. Purchaser understands and has been advised the driving of a vehicle on public streets or highways could result in criminal or civil penalties.

Prop 65

Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.

Learn More: www.p65warnings.ca.gov

Q and A

Product Questions

No questions yet. Be the first to ask the question!